ARNO - каталог точение и обработка резьбы 2013
для размещения заказа - info@arno-tools.ru
Indexable Inserts – Preselection
ISO
Material
Possible cutting materials
Unalloyed steel and
cast steel
Carbide
Cermet
Low alloyed steel and
cast steel
P
High alloyed steel, high alloyed tool
steel and cast steel
Stainless steel and
cast steel
M Stainless steel and
cast steel
K Cast iron
Cast iron with nodular graphite
Malleable iron
Aluminum and
aluminum alloys
N
Copper and copper alloys
(bronze/brass)
Non-ferrous materials
Duroplastics, reinforced plastics, hard
rubber
High temperature resistant alloys
S
Titanium alloys
H Hardened steel
Carbide
Carbide -
High positive geometry
Cermet
Carbide
Cermet
HSS
Carbide
Carbide -
High positive geometry
Cermet
HSS
Carbide
Carbide -
High positive geometry
HSS
Carbide
Carbide -
High positive geometry
CBN
Carbide
Carbide -
High positive geometry
PKD
Carbide -
High positive geometry
PCD
Carbide -
High positive geometry
Carbide
Carbide -
High positive geometry
HSS
Carbide
Carbide -
High positive geometry
PCD
HSS
CBN
Recommended geometries
Finishing
negative
-NS1
-AQ
-NFC
-NWC
-B
-S
-NS1
-AQ
-NFC
-NWC
positive
-AB
-PF2
-PMS
-PS2
-WMS
-AQ
-PMC
-AB
-PF2
-PMS
-PS2
-WMS
-ACB
-ALU
-ASF
-AWI
-AQ
-PMC
Medium machining
negative
-K
-NA
-NM1
-NM2
positive
-WMS
-PMS
-AM
-PM1
-B
-C
-NFC
-NMC
-NWC
-K
-NA
-NM1
-NM2
-PMC
-NFC
-NMC
-NWC
-NA
Roughing
negative
-NM1
-NMG1
-NR1
positive
-C
-NMC
-PMC
-AQ
-NWC
-NS1
-AQ
-B
-NFC
-S
-EX
-NS1
-EX
-AQ
-PMC
-AB
-PF2
-PMS
-PS2
-WMS
-ACB
-ALU
-ASF
-AQ
-PMC
-PF2
-PMS
-PS2
-WMS
-ACB
-AEC
-ALU
-ASF
-AWI
-NMC
-NWC
-K
-NA
-NM1
-NM2
-B
-C
-NMC
-NWC
-K
-NM1
-NM2
-NMR
-VA
-K
-NA
-PMC
-AM
-PM1
-NM1
-NMG1
-NR1
-PMC
-C
-AM
-PM1
-WMS
-NM1
-NMG1
-NR1
-AM -NMG1
-ACB
-ALU
-ASF
-PS
-AEC
-PF2
-ACB
-ACB
-ALU -ALU
-AWI -AWI
-ASF
-ACB
-ACB
-ALU -ALU
-ASF -AWI
-AWI
-ACB
-ACB
-ALU -ALU
-ASF -AWI
-AWI
-EX -NMR
-ACB
-ALU
-AWI
-ACB
-ALU
-AWI
-ACB
-ALU
-AWI
-ACB
-ALU
-ASF
-AWI
-EX
-ACB
-ALU
-AWI
-ACB
-ALU
-AWI
-ACB
-ACB
-ALU -ALU
-ASF -AWI
-AWI
3
Geometries are available for the corresponding machining procedures.
Remark: CBN grades should only be used for machining hard materials above 48HRC.
info@arno-tools.ru
www.arno-tools.ru
ARNO®-Werkzeuge | Drehen | Turning | Точение 159