ARNO - монолитный осевой инструмент 2015 EN
для размещения заказа - info@arno-tools.ru
Recommended cutting data Solid carbide end-mill and PM-HSS end-mill
Design AFR
Solid carbide end-mill
ISO Material
P
M
K
N
S
H
General construction steel
Free cutting steel
Case hardened steel, non alloyed
Alloyed case hardened steel
Tempering steel, non alloyed
Tempering steel, non alloyed
Tempering steel, alloyed
Tempering steel, alloyed
Steel castings
Nitriding steel
Nitriding steel
Roller bearing steel
Spring steel
High-speed steel
Cold working tool steel
Hot working tool steel
Steel and sulphured cast stainless steel
Stainless steel, ferritic
Stainless steel, martensitic
Stainless steel, ferritic/martensitic
Stainless steel, austenitic/ferritic
Stainless steel, austenitic
Heat resistant steel
Grey cast iron with lamellar graphite
Grey cast iron with lamellar graphite
Speroidal cast iron
Speroidal cast iron
White cast iron, tempered
White cast iron, tempered
Black cast iron, tempered
Black cast iron, tempered
Aluminium (non alloyed, low alloyed)
Aluminium alloys < 0,5% Si
Aluminium alloys 0,5%-10% Si
Aluminium alloys 10%-15% Si
Aluminium alloys > 15% Si
Copper (non alloyed, low alloyed)
Copper wrought alloys
Special copper alloys
Special copper alloys
Special copper alloys
Short-chipping brass, bronze, red bronze
Long-chipping brass
Thermoplastics
Duroplastics
Fibre-reinforced plastics
Magnesium and magnesium alloys
Graphite
Tungsten and tungsten alloys
Molybdenum and molybdenum alloys
Pure nickel
Nickel alloys
Nickel alloys
Nickel-chromium alloys
Nickel and cobalt alloys
Nickel and cobalt alloys
Heat resistant alloys
Nickel-cobalt-chromium alloys
Pure titanium
Titanium alloys
Titanium alloys
Tempered steel
Tempered steel
Tempered steel
Tempered steel
Tempered steel
Strength Correction
[N/mm2] factor [x fz]
< 800
< 800
< 800
< 1000
< 850
< 1000
< 800
< 1300
< 850
< 1000
< 1200
< 1200
< 1200
< 1300
< 1300
< 1300
< 850
< 750
< 900
< 1100
< 850
< 750
< 1100
100-350
300-1000
300-500
550-800
350-450
500-650
350-450
500-700
< 350
< 500
< 400
< 400
< 400
< 350
< 700
< 200 HB
< 300 HB
> 300 HB
< 600
< 600
1,2
1,2
1,2
1
1,2
1
1,2
0,8
1,2
0,8
0,8
0,8
0,8
0,8
0,8
0,8
1
1
1
0,9
1
1
0,9
1
1
1
1
1
1
1
0,8
Roughing and
full slot milling
VHM
AlCrN
Vc [m/min]
150-170
170-190
140-170
100-140
140-170
120-140
100-140
100-120
150-170
140-170
80-120
80-120
100-130
100-120
100-120
80-100
100-120
80-100
100-120
80-100
Peripheral- and
contour milling
VHM
AlCrN
Vc /span>[m/min]
170-200
190-220
170-190
140-180
170-190
140-160
140-170
120-160
170-200
170-190
120-150
120-150
130-150
120-140
120-140
100-120
120-140
100-120
120-140
100-120
< 850
< 850
< 1300
< 1300
< 1400
< 1300
< 900
< 700
< 1200
< 45 HRC
46-55 HRC
56-60 HRC
61-65 HRC
65-70 HRC
PM-HSS end-mill
Roughing and
full slot milling
PM-HSS
TiAlN
Vc [m/min]
60-70
60-70
60-70
30-40
30-40
30-40
30-40
30-35
30-35
25-30
25-30
25-30
25-30
25-35
25-35
25-35
25-35
20-30
15-25
25-35
30-35
25-30
40-55
30-40
35-45
35-45
40-50
40-50
35-45
30-40
Peripheral- and
contour milling
PM-HSS
TiAlN
Vc [m/min]
50-60
50-60
50-60
25-35
25-35
25-35
25-35
25-30
25-30
25-30
20-25
20-25
20-25
20-25
20-30
20-30
20-30
20-30
15-25
10-20
20-30
25-30
20-25
35-45
25-35
30-40
30-40
35-45
35-45
30-40
25-35
The recommended cutting data are only approximate values. It may be necessary to adjust them to each individual machining application.
ARNO®-Werkzeuge | VHM-/PM-HSS Werkzeuge | Solid carbide-/PM-HSS Tools 199
info@arno-tools.ru
www.arno-tools.ru