ARNO - каталог сверление 2013 EN
Recommended cutting data
для размещения заказа - info@arno-tools.ru
SHARK-DRILL®
Recommended cutting data
SHARK-DRILL®
SchnittwerteSHARK-DRILL®
SchnittwerteSHARK-DRILL®
HSS inserts
ISO
Material
Cutting speed
Vc
1
[N/mm2]
[m/min] [m/min] [mm/rev] [mm/rev] [mm/rev] [mm/rev] [mm/rev] [mm/rev] [mm/rev]
Unalloyed steel and cast steel
e.G. 9SMn28; 9SMnPb28; 10SPb20
Structual steel
e.G. St33; St37-2; St44-2; St52; St60
None- and low alloy steel as well as
carbon steel and case hardened steel
e.G. C15; C22; 20Mn5; Ck45
P
Alloys steel
e.G. 42CrMo4; 16MnCr5; 36CrNiMo4
14NiCrMo13-4; Ck75; Ck101; 17CrNiMo8,
35CrMo4; 41Cr4; 50MnSi4
High alloys steel
e.G. 41CrAlMo7; 36CrNiMo4;
32NiCrMo14-5
Tool steel
e.G. C75W; 102Cr6; 105WCr6; X153CrMoV12
M Stainless steel and
cast steel
Cast iron
e.G. GG25; GG40
K Cast iron with nodular graphite
e.G. GGG50
Malleable cast iron
e.G. GTS70
Aluminium alloys, long chipping
e.G. AlMgSiPb; AlCuMg1; AMgSi1
Casted aluminium alloys
e.G. G-AlSi10Mg; G-ALSi12
N Copper and copper alloys
(brass / bronze)
Non-ferrous materials
High temperature resistant alloys
e.G. Inconell, Hasteloy, Nimonic,
S Waspaloy, Monel
Titanium alloys / Titan
e.G. Ti99,5; Ti Al6V4; TiCu2
Hardened steel
H Hard cast iron
Hardened cast iron
austenitic and austenitic/ferritic
chilled
pearlitic, ferritic
pearlitic, martensitic
ferritic
pearlitic
ferritic
pearlitic
not heat treatable
heat treatable, heat-treated
12% Si, hardened
12% Si, heat treatable, hardened
12% Si, not heat treatable
Lead alloys, Pb>1%
Brass, bronze
Aluminium bronze
Copper and electrolyte copper
Duroplastics
Re- inforced plastics
Hard rubber
Fe-alloyed annealed
heat - treated
Ni- or
annealed
Co based casting
heat - treated
Pure titan
hardened and tempered
hardened and tempered
casting
hardened and tempered
up to 500 80 86 0.18 0.25 0.33 0.41 0.51 0.58
500-850 64 73 0.15 0.25 0.33 0.41 0.51 0.58
350-500 55 60 0.15 0.25 0.3 0.35 0.45 0.52
500-850 45 51 0.13 0.23 0.25 0.3 0.4 0.47
850-1200 40 43 0.1 0.2 0.23 0.25 0.35 0.43
bis 450
64 74 0.15 0.23 0.3 0.38 0.47 0.58
450-750 60 70 0.13 0.2 0.25 0.36 0.45 0.52
750-900 55 65 0.13 0.2 0.25 0.36 0.45 0.52
900-1100 51 60 0.1 0.18 0.23 0.3 0.4 0.47
bis 600
60 65 0.15 0.2 0.25 0.36 0.42 0.47
600-800 55 60 0.13 0.2 0.25 0.36 0.42 0.47
800-950 51 55 0.13 0.18 0.25 0.36 0.42 0.47
950-110 47 51 0.1 0.15 0.23 0.3 0.37 0.42
1100-1250 45
48 0.08 0.15 0.23 0.3 0.37 0.42
600-1000 30
35 0.13 0.18 0.23 0.25 0.35 0.42
1000-1200 25 27 0.1 0.13 0.23 0.25 0.35 0.42
1200-1350 20
22 0.08 0.11 0.2 0.23 0.3 0.4
500-700 32 35 0.1 0.15 0.2 0.25 0.3 0.35
700-950 25 28 0.1 0.15 0.2 0.25 0.3 0.35
450-610 30 33 0.09 0.19 0.2 0.29 0.37 0.42
610-930 25 29 0.09 0.16 0.19 0.25 0.3 0.37
500-700 61 70 0.16 0.29 0.37 0.47 0.57 0.65
700-850 45 50 0.14 0.19 0.24 0.3 0.37 0.44
850-1100 38
42 0.11 0.16 0.19 0.24 0.29 0.37
540 50 57 0.16 0.22 0.3 0.4 0.45 0.5
850 45 50 0.13 0.17 0.22 0.28 0.35 0.45
450 50 57 0.16 0.22 0.3 0.4 0.45 0.5
780 45 50 0.13 0.17 0.22 0.28 0.35 0.45
200 210 250 0.12 0.17 0.28 0.34 0.56 0.65
335 125 140 0.2 0.34 0.4 0.45 0.57 0.65
250 200 240 0.2 0.33 0.41 0.48 0.56 0.64
300 160 190 0.2 0.33 0.41 0.48 0.56 0.64
450 140 160 0.18 0.3 0.38 0.45 0.56 0.64
370 102 117 0.18 0.3 0.4 0.5 0.6 0.7
300 123 138 0.19 0.3 0.42 0.52 0.62 0.72
500 68 77 0.16 0.29 0.37 0.47 0.57 0.67
200 46 51 0.06 0.09 0.16 0.21 0.26 0.36
The cutting datas are depending on the available coolant supply.
Starting datas are the same as aluminium alloys, long chipping.
Air coolant is recommended.
700
980
850
1100
1230
500-700
700-1050
1020-1365
1365-1850
1365
2090
12
–
12
–
8
13
12
22
13
21
–
13 0.08 0.17 0.21 0.25 0.3 0.35
–––––––
13 0.08 0.17 0.21 0.25 0.3 0.35
–––––––
11 0.08 0.14 0.19 0.21 0.26 0.32
15 0.09 0.19 0.21 0.25 0.31 0.37
15 0.09 0.16 0.19 0.2 0.26 0.31
30 0.09 0.16 0.2 0.24 0.3 0.42
15 0.06 0.13 0.19 0.2 0.26 0.3
29 0.08 0.15 0.2 0.23 0.3 0.38
–––––––
0.7
0.7
0.65
0.6
0.5
0.7
0.6
0.6
0.55
0.55
0.55
0.55
0.5
0.5
0.5
0.5
0.45
0.41
0.41
0.52
0.47
0.72
0.52
0.42
0.6
0.5
0.6
0.5
0.65
0.65
0.64
0.64
0.64
0.75
0.76
0.72
0.41
0.35
–
0.35
–
0.32
0.4
0.31
0.47
0.4
0.43
–
Please note that the recommended cutting datas are a starting reference point in combination with the coolant figures on page 103 in the catalogue “Drillsystem
SHARK-Drill®”. Also important is that the basic conditions are on an average. For technical support please contact our application engineers.
Carbide inserts
ISO Material
Cutting speed
Vc
[N/mm2]
[m/min]
[m/min]
[mm/rev]
[mm/rev]
[mm/rev]
[mm/rev]
[mm/rev]
Unalloyed steel and cast steel
e.G. 9SMn28; 9SMnPb28; 10SPb20
Structual steel
e.G. St33; St37-2; St44-2; St52; St60
None- and low alloy steel as well as
carbon steel and case hardened steel
e.G. C15; C22; 20Mn5; Ck45
P
Alloys steel
e.G. 42CrMo4; 16MnCr5; 36CrNiMo4
14NiCrMo13-4; Ck75; Ck101; 17CrNiMo8,
35CrMo4; 41Cr4; 50MnSi4
High alloys steel
e.G. 41CrAlMo7; 36CrNiMo4;
32NiCrMo14-5
Tool steel
e.G. C75W; 102Cr6; 105WCr6; X153CrMoV12
M Stainless steel and
cast steel
Cast iron
e.G. GG25; GG40
K Cast iron with nodular graphite
e.G. GGG50
Malleable cast iron
e.G. GTS70
Aluminium alloys, long chipping
e.G. AlMgSiPb; AlCuMg1; AMgSi1
Casted aluminium alloys
e.G. G-AlSi10Mg; G-ALSi12
N Copper and copper alloys
(brass / bronze)
Non-ferrous materials
High temperature resistant alloys
e.G. Inconell, Hasteloy, Nimonic,
S Waspaloy, Monel
Titanium alloys / Titan
e.G. Ti99,5; Ti Al6V4; TiCu2
Hardened steel
H Hard cast iron
Hardened cast iron
austenitic and austenitic/ferritic
chilled
pearlitic, ferritic
pearlitic, martensitic
ferritic
pearlitic
ferritic
pearlitic
not heat treatable
heat treatable, heat-treated
12% Si, hardened
12% Si, heat treatable, hardened
12% Si, not heat treatable
Lead alloys, Pb>1%
Brass, bronze
Aluminium bronze
Copper and electrolyte copper
Duroplastics
Re- inforced plastics
Hard rubber
Fe-alloyed annealed
heat - treated
Ni- or
annealed
Co based casting
heat - treated
Pure titan
hardened and tempered
hardened and tempered
casting
hardened and tempered
up to 500
115
125
0.15 0.21 0.28 0.35
500-850
90
105 0.13 0.21 0.28 0.35
350-500
85
95 0.13 0.21 0.26 0.3
500-850
68
75 0.11 0.2 0.21 0.26
850-1200
62
70 0.09 0.17 0.2 0.21
bis 450
110
120
0.13
0.2
0.26 0.32
450-750
85
95 0.11 0.17 0.21 0.31
750-900
70
85 0.11 0.17 0.21 0.31
900-1100
60
70 0.09 0.15 0.2 0.26
bis 600
90
100 0.13 0.17 0.21 0.31
600-800
80
90 0.11 0.17 0.21 0.31
800-950
70
85 0.11 0.15 0.21 0.31
950-110
67
75 0.09 0.13 0.2 0.26
1100-1250 60
65 0.07 0.13 0.2 0.26
600-1000
55
60 0.11 0.15 0.2 0.21
1000-1200 50
55 0.09 0.11 0.2 0.21
1200-1350 44
50 0.07 0.09 0.17 0.2
500-700
60
65 0.09 0.13 0.17 0.21
700-950
45
50 0.09 0.13 0.17 0.21
450-610
58
65 0.09 0.16 0.19 0.24
610-930
44
50 0.09 0.14 0.16 0.2
500-700
103
123
0.14
0.2
0.26 0.37
700-850
80
95
0.1 0.16 0.19 0.26
850-1100
70
84
0.1 0.14 0.16 0.22
540 100 120 0.12 0.17 0.2 0.29
850 75 95 0.1 0.14 0.18 0.26
450 105 125 0.12 0.17 0.2 0.29
780 78 97 0.1 0.14 0.18 0.26
200 410 450 0.1 0.17 0.27 0.33
335 275 305 0.12 0.29 0.37 0.52
250 400 450 0.2 0.31 0.4 0.48
300 350 380 0.2 0.3 0.4 0.48
450 250 280 0.18 0.28 0.36 0.46
370 130 145 0.15 0.23 0.28 0.38
300 160 185 0.16 0.24 0.29 0.39
500 100 110 0.14 0.2 0.26 0.37
200 100 120 0.05 0.09 0.1 0.16
The cutting datas are depending on the available coolant supply.
Starting datas are the same as aluminium alloys, long chipping.
Air coolant is recommended.
700
980
850
1100
1230
500-700
700-1050
1020-1365
1365-1850
1365
2090
29
–
29
–
21
33
29
40
24
30
–
32 0.08 0.16 0.2 0.24
–––––
32 0.08 0.16 0.2 0.24
–––––
25 0.08 0.12 0.16 0.18
39 0.09 0.16 0.19 0.24
34 0.09 0.14 0.16 0.22
44 0.09 0.14 0.22 0.25
26 0.06 0.11 0.16 0.22
35 0.07 0.12 0.18 0.22
–––––
0.43
0.43
0.38
0.34
0.3
0.4
0.38
0.38
0.34
0.36
0.36
0.36
0.31
0.31
0.3
0.3
0.26
0.26
0.26
0.3
0.25
0.45
0.37
0.32
0.45
0.37
0.4
0.37
0.38
0.6
0.5
0.5
0.48
0.45
0.45
0.42
0.25
0.3
–
0.3
–
0.25
0.3
0.28
0.32
0.27
0.27
–
Please note that the recommended cutting datas are a starting reference point in combination with the coolant figures on page 103 in the catalogue “Drillsystem
SHARK-Drill®”. Also important is that the basic conditions are on an average. For technical support please contact our application engineers.
1
100 ARNO®-Werkzeuge | Bohren | Drilling | Foratura
Alle Angaben in mm / Dimensions in mm / Tutte le dimensioni in mm
info@arno-tools.ru
www.arno-tools.ru
Alle Angaben in mm / Dimensions in mm / Tutte le dimensioni in mm
ARNO®-Werkzeuge | Bohren | Drilling | Foratura 101